2 battary mod problem

Home › Forums › Bit Char-G, Digi-Q and other Micros › Bit CharG and Micro Radio Controlled – Technical › 2 battary mod problem

Viewing 12 reply threads
  • Author
    Posts
    • August 8, 2003 at 5:42 pm #11228
      Admin
      Participant
      • Posts: 5952

      I did a 2 batt mod to my bit char g last night, i check the batt votage using a voltmeter and the voltage is 2.4 something (by checking the + and – port under the car,
      so the mod was success, But it seems that the car can never be fully charged, the car run like hell on the charger but run like turtle after detached. what’s happening???
      please help!!!!!

    • August 8, 2003 at 6:09 pm #21747
      VR-4
      Participant
      • Posts: 400

      did you do the controler mod?

    • August 8, 2003 at 6:20 pm #21748
      Admin
      Participant
      • Posts: 5952

      I cut the wire connecting the charge panel and the remote control, then directly connect the battery port to the charge panel? is that correct?

      or I must use a 3 or 4 battery charger to chare the car???

    • August 8, 2003 at 6:20 pm #21749
      KingRX7
      Participant
      • Posts: 129

      what are you using to charge it?

    • August 8, 2003 at 6:24 pm #21750
      VR-4
      Participant
      • Posts: 400

      i charge mine of my intell peek charger.

      try useing a 4 cell pack and let it sit for about 45-60 sec

    • August 8, 2003 at 6:35 pm #21754
      KingRX7
      Participant
      • Posts: 129

      DONT DRIVE IT ON THE CHARGER IF UR USING A 4CELL PACK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! i burnt up 2 cars doing it

    • August 8, 2003 at 6:37 pm #21755
      Admin
      Participant
      • Posts: 5952

      shall I directly connect a 4 battery pack to the + and – port of the charge panel of the remote??

    • August 8, 2003 at 6:39 pm #21756
      Admin
      Participant
      • Posts: 5952

      by the way is there a possibility that the 2.4V (I use Charged battery) from the remote is not high enough to chare the 2.4V in the Bit Char g?

    • August 8, 2003 at 6:40 pm #21757
      KingRX7
      Participant
      • Posts: 129

      i just unsoldered the charging dock from the circut board and kept those wires and then soldered the black to black and red to red on the battery pack charger.

    • August 8, 2003 at 6:42 pm #21760
      VR-4
      Participant
      • Posts: 400

      i did the same till i hooked a charge deck upto my rc car charger

    • August 8, 2003 at 7:02 pm #21766
      jamiekulhanek
      Participant
      • Posts: 2563

      You all seem to be headin’ in the right direction 🙂 A 4 cell pack connected to the car seems to work best, keep it connected for about 2 minutes and you will have a lovely long runtime :smiley16:

    • August 9, 2003 at 3:16 am #21811
      leonli17
      Participant
      • Posts: 602

      Conraha—don’t use Rechargeble batteries for a charger. if your controller is only for control not charging then it’s fine. But if u charge the Dual Cell cars they won’t charge because the rechargeble batteries only have 2.4-2.5V when Alkaline batteries has 3V.

    • August 10, 2003 at 3:33 pm #21835
      Prowler3
      Participant
      • Posts: 121

      nice gallery leonli17

  • Author
    Posts
Viewing 12 reply threads
  • You must be logged in to reply to this topic.