Admin
Forum Replies Created
-
AuthorPosts
-
Thats o.k. mate..
where can one buy one of these it looks preety cool n small enough to run in my pond 😛I have an IWI02 with 2×6 IRF 7317 ans I run with the X-Speed pro with a 12t pignon 😉
I can tell you then the police isn””t happy(64km/h-40mph)!!!
And I haven””t got any problems
I run with 2×2 2/3 AA and it””s okay.
But I think than the Palzamatomic is better because is has moretorque, so better on littletrack andthe X-Speed pro drawes to muchAMP for AAA batreries.
So, have lot”s of fun with your crazy cars 😉
Edited by – Villou on 04 June 2005 01:11:52
I will be in Singapore in 2 weeks time. Does any know where i should go to get one? What other mod part should i get? (budget of AUS$400.00 with a new MR 02)
Thanks for your prompt reply. Can you please let me know where i can get a good price in Sydney for mini z mr02.
thks
Real funny
You surely have lot’s of fun when you drive that 😀
But, I ask to see wath it does on a circuit :p
Has anyone used Grand Cell batts in their mini z. If so are they any better than regular batts??? I Saw an ad on ebay for some Grand Cell batteries that were made in AUS (down unda).The ad claimed thatthese batts are a big hit inAUS (Ilive in USA,DC) and that they have longer run times than regular batts. Just curious if this is for real or just some BS. thanks……………………..jd in dc.
ya i knew about those but i aint got the dough for it. it cost around 50 buks for each isnt it? btw where did u get it? its the irider that u r talking about rite?
ya i knew about those but i aint got the dough for it. it cost around 50 buks for each isnt it? btw where did u get it? its the irider that u r talking about rite?
Excellent read ph2t….the need for speed drives some of us to very interesting discoveries. I also fiddled with a FA 130 motor that came with the TYCO CROSSFIRE, I should add also that the performance sphere I m talking about is in no way comparable to what you geeza’s get up to, however much was learnt. The ‘out of box’ car would wobble it’s way up to a pathetic 6km/h and was immediately junked but the two motors,pcb and shell were retained. After much work a more acceptable vehicle was produced (centrifigal clutch steering is one of it’s virtues) however the motor mods may interest some of you…with 2.4volts and 8to1 reduction it’s on road speed went up to 7.5km/h (were talkin’ crap car speed here) and run time of 40 minutes. The motor’s origin is unknown but probably one of Kowloons finest and would run at a steady 11500/12000 rpm but was unusual in that it is fitted with carbon brush gear and not the copper fingers. A new end casing was made up that allowed the brushes to be advanced from 0 to 30 degrees, also mounting the said brush gear on an adjustable slide enable’s one to raise or lower the contact point on the armature to ensure that they are truly at 180 degrees to each other and finally two eccentrics were squeezed in so that brush pressure could be varied.
This bumped motor speed up to 15000 in forward and 13500 in reverse, acceptable results
I guess with such a plain motor but the big jump came when the car was run on 3.6 volts with 3 AAA’s,motor speed increased to 21000 and on road speedwas lifted to 14.8 km/hwhich is about all an old guy like me can handle…the drawback with this pattern of motor is having one brush leading and one trailing as they both should be trailing.
I’m gonna buy a X Ray M18 but I’d like to boost ma Iwaver more and more and more 😀
Actually, it isn’t a Iwaver02 anymore but it’s a TAGU 😉
The IWI PCB is really different of a Kyosho PCB because de FETS are really betters 😉
But, we don’t care about fets, mine are solids 😉 I just care about the reception…
I’m waiting for others answers …
I m gonna buy a X Ray M18 but I’d like to boost ma Iwaver more and more and more 😀
Actually, it isn’t a Iwaver02 anymore but it’s a TAGU 😉
The IWI PCB is really different of a Kyosho PCB because de FETS are really betters 😉
But, we don’t care about fets, mine are solids 😉 I just care about the reception…
I’m waiting for others answers …
Oh ic..thnx for replying. I’m not actually racing yet but i want to race.
Btw, is a LRP F1 supa reverseESC negood?
All cons and pro will be appreciated 🙂
I would alsolike ur opinions on these stockers; epic binary2 stock proand trinitymonster.
MXM The reason why some electronic devices or cell phones have no antenna’s, is because they use (micro strip antenna’s) ecth on the PCB.THE antenna load is match to the circuits input and output stages of the amplifiers stage (impedances).Its called RF impedance matching.In RF circuit design. This is not a theory. ITs a fact.Look up impedance matching for RF CIRCUITS.And Micro strip PCB antenna’s.Or PCB’s ecth antenna’s.You could try what TRASH commented on. Using the magnetic wire and, form a loop coil to form a antenna but you still have to match the load with the impedances of the last stages of the amplifier to any antenna you use for this kind of load.If you don’t do any impedances matching of your load for your loop antenna and size of the wire and lenght in will not work.And the loop coil that TRASH commented on would be the easise way and cheapest. The guitar wire that PH2T used is just a wire the same as a dipole antenna with the, I guest the same lenght of wire he had in the car in the first place. he just changed the type of wire used. It did not change the load of the wire or the impedances of this wire thats why I assumed it worked in his car.MXM you can try no wire but the car might not work. Or you will get a short range it depends. GOOD LUCK.:smiley16:
MXM The reason why some electronic devices or cell phones have no antenna’s, is because they use (micro strip antenna’s) ecth on the PCB.THE antenna load is match to the circuits input and output stages of the amplifiers stage (impedances).Its called RF impedance matching.In RF circuit design. This is not a theory. ITs a fact.Look up impedance matching for RF CIRCUITS.And Micro strip PCB antenna’s.Or PCB’s ecth antenna’s.You could try what TRASH commented on. Using the magnetic wire and, form a loop coil to form a antenna but you still have to match the load with the impedances of the last stages of the amplifier to any antenna you use for this kind of load.If you don’t do any impedances matching of your load for your loop antenna and size of the wire and lenght in will not work.And the loop coil that TRASH commented on would be the easise way and cheapest. The guitar wire that PH2T used is just a wire the same as a dipole antenna with the, I guest the same lenght of wire he had in the car in the first place. he just changed the type of wire used. It did not change the load of the wire or the impedances of this wire thats why I assumed it worked in his car.MXM you can try no wire but the car might not work. Or you will get a short range it depends. GOOD LUCK.:smiley16:
there’s a charlie at toyworld… I know there’s a charlie at hobby garage next door to toyworld…
well… if ya know anyone wantin a bling bling mini thing… 😛 let us know… prolly sellin it as a roller. but next time i’ll be more prep’d and hopefully have a diff car… mmmm… traction…
Azzy
i fixed my slipping slipper today. now my minferno screams. don’t you hate getting beat by a little kid with someone elses stock out of the box car.
was a heap of fun though. can’t wait to get a brushless for it.I’m guessin your terry… pity the stock mini-T won… I had no traction and ended up striping my servo in the finals…
can a 400 size bolt straight in or do I have to mod the plate… I’m gonna order one soon…
was hobbyrama in bris vegas. they only had it delivered earlier that day. if you are on the north side of brisbane talk to charlie at toyworld lawnton. he should be able to do a better price then that when he gets his stock.
i bought a half 8 from my lhs for AU$250. Quite reasonable i think. Definately needs more grunt. Will have to ‘invest’ in a brushless i think. Might nearly be quick enough then.
HI Again: That website does work. I guset it might be where you are. Or something when down on that site.Can you review my first question again and try that website a few more times.I come from the states.Thats why the website-page i inclued works for me.Try these. http://www.elenco.com.usa or http://www.elenco.com.us OR http://www.elenco.com the last one should work.When you get to there website go to there home page and look for there project kit remote radio control car kit. OR look for there user manuals. THE ONE TO LOOK FOR IS (rcc-7k.)belive me its there. THANK YOU… PS Let me know if you in to the site. I HOPE YOU OR SOMEONE OUT THERE COULD HELP ME.
😯HI Again: That website does work. I guset it might be where you are. Or something when down on that site.Can you review my first question again and try that website a few more times.I come from the states.Thats why the website-page i inclued works for me.Try these. http://www.elenco.com.usa or http://www.elenco.com.us OR http://www.elenco.com the last one should work.When you get to there website go to there home page and look for there project kit remote radio control car kit. OR look for there user manuals. THE ONE TO LOOK FOR IS (rcc-7k.)belive me its there. THANK YOU… PS Let me know if you in to the site. I HOPE YOU OR SOMEONE OUT THERE COULD HELP ME.
😯Hi Again: Thanks for this info. But can you elaborate more on this timing function. Is this the timing, for the pulses of the single data to control the car. like used in a 555 timer circuit. If not. Can you explain this so i could understand this function better on this chip.Better yet. Give me an :example! Also by using Ohms-law how do you determine the resistor for the OSC PINS. PLEASE EXPLAIN! PS I could not open or get these last three datasheets on these websites some chineese message tops up; Thank you once again.
http://homepages.paradise.net.nz/bhabbott/tyco/sm6136.pdf
Also the HES30xx are the same.
http://homepages.paradise.net.nz/bhabbott/tyco/hes3018.pdf
http://homepages.paradise.net.nz/bhabbott/tyco/hes3017.pdf.
🙂 -
AuthorPosts
